View MIC4414_5762899.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC4414/4415 1.5a, 4.5v to 18v, low-side mosfet driver micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com august 2012 m9999-080112-a general description the MIC4414 and mic4415 are low-side mosfet drivers designed to switch an n-channel enhancement type mosfet in low-side switch applications. the MIC4414 is a non-inverting driver and the mic4415 is an inverting driver. these drivers feature short delays and high peak current to produce precise edges and rapid rise and fall times. the MIC4414/15 are powered from a 4.5v to 18v supply and can sink and source peak currents up to 1.5a, switching a 1000pf capacitor in 12ns. the on-state gate drive output voltage is approx imately equal to the supply voltage (no internal regulators or clamps). high supply voltages, such as 10v, are appropriate for use with standard n-channel mosfets. low supply voltages, such as 5v, are appropriate for use with many logic-level n- channel mosfets. in a low-side configuration, the driver can control a mosfet that switches any voltage up to the rating of the mosfet. the MIC4414 and mic4415 are available in an ultra-small 4-pin 1.2mm x 1.2mm thin qfn package and is rated for ?40c to +125c junction temperature range. data sheets and support documentation can be found on micrel?s web site at: www.micrel.com . features ? ultra-small 4-pin 1.2mm x 1.2mm thin qfn package ? +4.5v to +18v operating supply voltage range ? 1.5a peak current ? 3.5 ? output resistance at 18v ? 9 ? output resistance at 5v ? low steady-state supply current ? 77a control input low ? 445a control input high ? 12ns rise and fall times into 1000pf load ? MIC4414 (non-inverting) ? mic4415 (inverting) ? -40c to +125c junction temperature range applications ? switch mode power supplies ? solenoid drivers ? motor driver _________________________________________________________________________________________________________________________ typical application
micrel, inc. MIC4414/mic4415 august 2012 2 m9999-080112-a ordering information part number marking configuration package junction temperature range lead finish MIC4414yft d9 non-inverting 4-pin 1.2mm x 1.2mm thin qfn -40c to +125c pb-free mic4415yft d8 inverting 4-pin 1.2mm x 1.2mm thin qfn -40c to +125c pb-free note: 1.thin qfn pin 1 identifier = ? ? pin configuration 1.2mm x 1.2mm thin qfn (top view) pin description pin number pin name pin function 1 out gate output: connection to gate of external mosfet. 2 gnd ground. 3 in control input: MIC4414: logic high drives the gate output above the supply voltage. logic low forces the gate output near ground. do not leave floating. mic4415: logic low drives the gate output above the supply voltage. logic high forces the gate output near ground. do not leave floating. 4 vdd supply voltage: +4.5v to +18v supply.
micrel, inc. MIC4414/mic4415 august 2012 3 m9999-080112-a absolute maximum ratings (1) vdd to gnd.................................................................+20v in to g nd....................................................... ?20v to +20v out to gnd.................................................................+20v junction temperature (t j ) ........................?55c to +150c storage temperature (t s).........................?55c to +165c esd rating (2) ................................................. esd sensitive operating ratings (3) vdd to gnd.................................................. +4.5v to +18v in to gnd........................................................... 0v to vdd junction temperature (t j ) ...................... . ? 40 ? c to +125 ? c thermal resistance 1.2mm x 1.2mm thin qfn ( ? jc ) ........................60c/w 1.2mm x 1.2mm thin qfn ( ? ja ) ......................140c/w electrical characteristics (4) 4.5v ? vdd ? 18v, c l = 1000pf; t a = 25c, bold values indicate ? 40c t j +125c. parameter condition min typ max units MIC4414: in = 0v, vdd = 18v mic4415: in = 5v, vdd = 18v 77 200 supply current MIC4414: in = 5v, vdd = 18v mic4415: in = 0v, vdd = 18v 445 1500 a in = logic low 0.8 v in voltage in = logic high 3 v in current 0v ? vin ? vdd -10 +10 a vdd = 5v, c l = 1000pf 30 output rise time vdd = 18v, c l = 1000pf 12 ns vdd = 5v, c l = 1000pf 33 output fall time vdd = 18v, c l = 1000pf 12 ns vdd = 5v, c l = 1000pf 52 delay time, in rising vdd = 18v, c l = 1000pf 29 ns vdd = 5v, c l = 1000pf 58 delay time, in falling vdd = 18v, c l = 1000pf 30 ns out = high -25 output offset voltage out = low 25 mv source 9 vdd = 5v, i out = 10ma sink 9 source 3.5 10 output resistance vdd = 18v, i out = 10ma sink 3.5 10 ? output reverse current 250 ma notes: 1. exceeding the absolute maximum rating may damage the device. 2. devices are esd sensitive. handling prec autions are recommended. human body model, 1.5k ? in series with 100pf. 3. the device is not guaranteed to function outside operating range. 4. specification for packaged product only.
micrel, inc. MIC4414/mic4415 august 2012 4 m9999-080112-a timing diagram source state sink state (p-channel on, n-channel off) (p-channel off, n-channel on) MIC4414/mic4415 operating states MIC4414 (non-inverting) mic4415 (inverting)
micrel, inc. MIC4414/mic4415 august 2012 5 m9999-080112-a typical characteristics MIC4414 on in=5v, off in=0v. mic4415 on in=0v, off in=5v. supply current vs. supply voltage 0 100 200 300 400 500 0 3 6 9 12 15 18 supply voltage (v) supply current (a) in = on in = off in bias current vs. supply voltage 0 0.2 0.4 0.6 0.8 1 0 3 6 9 12 15 18 supply voltage (v) in bias current (a) in = on output source resistance vs. supply voltage 0 3 6 9 12 15 0369121518 supply voltage (v) on resistance ( ? ) i out = 10ma output sink resistance vs. supply voltage 0 3 6 9 12 15 0369121518 supply voltage (v) on resistance ( ? ) i out = 10ma rise and fall time vs. supply voltage 0 12 24 36 48 60 0 3 6 9 12 15 18 supply voltage (v) time (ns) c l =1000pf in = 1mhz, 50% duty cycle fall rise delay time vs. supply voltage 0 16 32 48 64 80 0 3 6 9 12 15 18 supply voltage (v) delay time (ns) in rise in fall peak output current vs. supply voltage 0.0 0.6 1.2 1.8 2.4 3.0 0 3 6 9 12 15 18 supply voltage (v) current (a) source sink supply current vs. temperature 0 100 200 300 400 500 -50 -25 0 25 50 75 100 125 temperature (c) supply current (a) vdd = 5v, in = on vdd = 18v, in = on vdd = 5v, in = off vdd = 18v, in = off output source resistance vs. temperature 0 2 4 6 8 10 12 14 -50 -25 0 25 50 75 100 125 temperature (c) on-resistance ( ? ) vdd = 5v i out = 3ma vdd = 18v i out = 3ma
micrel, inc. MIC4414/mic4415 august 2012 6 m9999-080112-a typical characteristics (continued) MIC4414 on in=5v, off in=0v. mic4415 on in=0v, off in=5v. output sink resistance vs. temperature 0 2 4 6 8 10 12 14 -50 -25 0 25 50 75 100 125 temperature (c) on-resistance ( ? ) vdd = 5v i out = 3ma vdd = 18v i out = 3ma rise and fall time vs. temperature 0 5 10 15 20 25 30 35 40 45 50 -50 -25 0 25 50 75 100 125 temperature (c) time (ns) fall rise vdd = 5v in = 1mhz, 50% duty cycle c l =1000pf rise and fall time vs. temperature 0 5 10 15 20 25 30 35 40 45 50 -50 -25 0 25 50 75 100 125 temperature (c) time (ns) vdd = 18v in = 1mhz, 50% duty cycle c l =1000pf rise fall delay time vs. temperature 0 10 20 30 40 50 60 70 80 -50 -20 10 40 70 100 130 temperature (c) time (ns) vdd = 5v i n fall i n rise delay time vs. temperature 0 10 20 30 40 50 60 70 80 -50 -20 10 40 70 100 130 temperature (c) time (ns) vdd = 18v in rise in fall supply current vs. load capacitance 0.1 1 10 100 1 10 100 capacitance (nf) supply current (ma) vdd = 5v duty cycle = 50% in = 1mhz in = 10khz in = 100khz supply current vs. load capacitance 0.1 1 10 100 1 10 100 capacitance (nf) supply current (ma) vdd = 18v duty cycle = 50% in = 1mhz in = 100khz in = 10khz output rise and fall time vs. load capacitance 0.01 0.1 1 10 100 1 10 100 capacitance (nf) time (s) vdd = 5v in = 1khz, 50% duty cycle fall rise output rise and fall time vs. load capacitance 0.01 0.1 1 10 100 1 10 100 capacitance (nf) time (s) vdd = 18v in = 1khz; 50% duty cycle rise fall
micrel, inc. MIC4414/mic4415 august 2012 7 m9999-080112-a typical characteristics (continued) MIC4414 on in=5v, off in=0v. mic4415 on in=0v, off in=5v. v dd supply current vs. frequency 0.1 1 10 100 0 1 10 100 1000 10000 in frequency (khz) vdd supply current (ma) vdd = 5v c l = 0pf c l = 1000pf c l = 2000pf c l = 5000pf c l = 10000pf v dd supply current vs. frequency 0.1 1 10 100 0 1 10 100 1000 10000 in frequency (khz) vdd supply current (ma) vdd = 18v c l = 10000pf c l = 5000pf c l = 2000pf c l = 1000pf c l = 0pf
micrel, inc. MIC4414/mic4415 august 2012 8 m9999-080112-a functional diagram functional description the MIC4414 is a non-inverting driver. a logic high on the in (control) pin produces gate drive output. the mic4415 is an inverting driver. a logic low on the in (control) pin produces gate drive output. the out is used to turn on an external n-channel mosfet. the out pin will be driven to 0v or vdd depending on the status of in pin. vdd vdd (supply) is rated for +4.5v to +18v. external capacitors are recommended to decouple noise. in in must be forced high or low by an external signal. a floating input will cause unpredictable operation. a high input turns on q1, which sinks the output of the 0.3ma and the 0.6ma current source, forcing the input of the first inverter low. hysteresis the control threshold voltage, wh en in is rising, is slightly higher than the control threshold voltage when in is falling. when in is low, q2 is on, which applies the additional 0.6ma current source to q1. forcing in high turns on q1 which must sink 0.9ma from the two current sources. the higher current through q1 causes a larger drain-to-source voltage drop across q1. a slightly higher control voltage is required to pull the input of the first inverter down to its threshold. q2 turns off after the first inverter output goes high. this reduces the current through q1 to 0.3ma. the lower current reduces the drain-to-source voltage drop across q1. a slightly lower control voltage will pull the input of the first inverter up to its threshold. drivers the second (optional) inverter permits the driver to be manufactured in inverting and non-inverting versions. the last inverter functions as a driver for the output mosfets q3 and q4. out out is designed to drive a capacitive load. the out voltage is either approximat ely the supply voltage or approximately ground, depending on the logic state applied to in. if in is high, and vdd (supply) drops to zero, the gate output will be floating (unpredictable). esd protection d1 protects vdd from negative esd voltages. d2 and d3 clamp positive and negative esd voltages applied to in. r1 isolates the gate of q1 from sudden changes on the in pin. d4 and d5 prevent q1?s gate voltage from exceeding the supply voltage or going below ground.
micrel, inc. MIC4414/mic4415 august 2012 9 m9999-080112-a application information the MIC4414 and mic4415 are designed to provide high peak current for charging and discharging capacitive loads. the 1.5a peak value is a nominal value determined under specific conditions. this nominal value is used to compare its relative size to other low-side mosfet drivers. the MIC4414 and mic4415 are not designed to directly switch 1.5a continuous loads. supply bypass a capacitor from vdd to gnd is recommended to control switching and supply transients. load current and supply lead length are some of the factors that affect capacitor size requirements. 4.7f or 10f ceramic or tantalum capacitor is suitable for many applications. low-esr (equivalent series resistance) metalized film capacitors may also be suitable. an additional 0.1f ceramic capacitor is suggested in parallel with the larger capacitor to control high-frequency transients. the low esr (equivalent series resistance) of ceramic and tantalum capacitors makes them especially effect ive, but also makes them susceptible to uncontrolled inrush current from low impedance voltage sources (such as nicd batteries or automatic test equipment). avoid instantaneously applying voltage, capable of very high peak current, directly to or near low esr capacitors without additional current limiting. normal power supply turn-on (slow rise time) or printed circuit trace resistance is usually adequate. circuit layout avoid long power supply and ground traces. they exhibit inductance that can cause voltage transients (inductive kick). even with resistive loads, inductive transients can sometimes exceed the ratings of the mosfet and the driver. when a load is switched off, supply lead inductance forces current to continue flowing and results in a positive voltage spike. inductance in the ground (return) lead to the supply has similar effects, except the voltage spike is negative. switching transitions momentarily draw current from vdd to gnd. this combines with supply lead inductance to create voltage transients at turn on and turnoff. transients can also result in slower apparent rise or fall times when driver?s ground shifts with respect to the control input. minimize the length of supply and ground traces or use ground and power planes when possible. bypass capacitors should be placed as close as practical to the driver. mosfet selection standard mosfet a standard n-channel power mosfet is fully enhanced with a gate-to-source voltage of approximately 10v and has an absolute maximum gate-to-source voltage of 20v. the MIC4414/15?s on-state output is approximately equal to the supply voltage. the lowest usable voltage depends upon the behavior of the mosfet. figure 1. using a standard mosfet logic-level mosfet logic-level n-channel power mosfets are fully enhanced with a gate-to-source voltage of approximately 5v and some of them have an absolute maximum gate- to-source voltage of 10v. they are less common and generally more expensive. the MIC4414/15 can drive a logic-level mosfet if the supply voltage, including transients, does not exceed the maximum mosfet gate-to-source rating (10v). figure 2. using a logic-level mosfet
micrel, inc. MIC4414/mic4415 august 2012 10 m9999-080112-a at low voltages, the MIC4414/15?s internal p- and n- channel mosfet?s on-resistance will increase and slow the output rise time. refer to ?typical characteristics? graphs. inductive loads switching off an inductive load in a low-side application forces the mosfet drain higher than the supply voltage (as the inductor resists change s to current). to prevent exceeding the mosfet?s drain-to-gate and drain-to- source ratings, a schottky diode should be connected across the inductive load. figure 3. switching an inductive load power dissipation the maximum power dissipation must not be exceeded to prevent die meltdown or deterioration. power dissipation in on/off switch applications is negligible. fast repetitive switching applications, such as smps (switch mode power supplies), cause a significant increase in power dissipation with frequency. power is dissipated each time current passes through the internal output mosfets when charging or discharging the external mosfet. power is also dissipated during each transition when some current momentarily passes from vdd to gnd through both internal mosfets. power dissipation is the product of supply voltage and supply current: dd dd d i v p ? ? equation 1 where: p d = power dissipation (w) v dd = supply voltage (v) i dd = supply current (a) supply current is a function of supply voltage, switching frequency, and load capacitance. determine this value from the ?typical characteristics: supply current vs. frequency? graph or measure it in the actual application. do not allow p d to exceed p d (max), as shown in the eq 2 . t j (junction temperature) is the sum of t a (ambient temperature) and the temperature rise across the thermal resistance of the package. in another form: 140 25 a d t 1 (max) p ? ? equation 2 where: p d (max) = maximum power dissipation (w) 125 = operating maximum junction temperature ( ? c) t a = ambient temperature ( ? c) 140 = package thermal resistance ( ? c/w) high-frequency operation although the MIC4414/15 driver will operate at frequencies greater than 1mhz, the mosfet?s capacitance and the load will affect the output waveform (at the mosfet?s drain). for example, an MIC4414/irl3103 test circuit using a 47 ? , 5w load resistor will produce an output waveform that closely matches the input signal shape up to about 500khz. the same test circuit with a 1k ? load resistor operates only up to about 25khz before the mosfet source waveform shows significant change. figure 4. mosfet capacitance effects at high switching frequency
micrel, inc. MIC4414/mic4415 august 2012 11 m9999-080112-a when the mosfet is driven o ff, the slower rise occurs because the mosfet?s output capacitance recharges through the load resistance (rc circuit). a lower load resistance allows the output to rise faster. for the fastest driver operation, choose the smallest power mosfet that will safely handle the desired voltage, current, and safety margin. the smallest mosfets generally have the lowest capacitance.
micrel, inc. MIC4414/mic4415 august 2012 12 m9999-080112-a evaluation board schematic bill of materials item part number manufacturer description qty. c1 grm188r71e104ka01d murata (1) 0.1f/25v ceramic capacitor, x7r, size 0603 1 c2012x5r1e475k tdk (2) grm21br61e475ka12l murata c2 08053d475kat2a avx (3) 4.7f/25v ceramic capacitor, x5r, size 0805 1 c3 (open) used as gate capacitor, different values q1 (open) u1 MIC4414yft mic4415yft micrel, inc. (4) 1.5a/4.5v to 18v low side mosfet driver 1 notes: 1. murata: www.murata.com . 2. tdk: www.tdk.com . 3. avx: www.avx.com . 4. micrel, inc.: www.micrel.com .
micrel, inc. MIC4414/mic4415 august 2012 13 m9999-080112-a pcb layout figure 5. MIC4414/15 evaluation board top layer figure 6. MIC4414/15 evaluation board bottom layer
micrel, inc. MIC4414/mic4415 august 2012 14 m9999-080112-a package information 4-pin 1.2mm x 1.2mm thin qfn (ft) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com micrel makes no representations or warranties with respect to t he accuracy or completeness of the information furnished in this data sheet. this information is not intended as a warranty and micrel does not assume responsibility for it s use. micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. no license, whether expre ss, implied, arising by estoppel or other wise, to any intellectual property rights is granted by this document. except as provided in micrel?s terms and conditions of sale for such products, mi crel assumes no liability whatsoever, and micrel disclaims any express or implied warranty relating to the sale and/or use of micrel products including l iability or warranties relating to fitness for a particular purpose, merchantability, or infringement of an y patent, copyright or other intellectual p roperty right. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in pers onal injury. life support devices or system s are devices or systems that (a) are in tended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2012 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC4414

	To Download MIC4414 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .